How to Replace a Kia Sportage Replacement Key

The key in many Kia models has a keyless entry system built into. This key typically resembles the remote control and is able to be replaced by a new one purchased from a Kia dealer or locksmith.

Key fobs might stop working for a variety of reasons, such as the battery of the coin is dead worn buttons water damage, signal interference and a damaged receiver module. Here are some guidelines on how you can get your Kia Sportage replacement key working again.

how to get a new kia key (official website) to replace the remote key or smart key

The battery in your 2011 kia optima key fob's intelligent key will eventually need to be replaced, whether it's a remote or a push-to-start one, or a standard metal key that is not equipped with transponder. This is especially when the vehicle displays a message that indicates that the smart or remote key is not powered by the battery.

Fortunately, it's an easy procedure. In order to replace the battery of the key fob remove the mechanical key from the slit at the back of the key fob. You then need to pry open the cover. A small screw is located inside the key fob to keep the battery in place. Remove the old battery by unwinding the screw using the help of a small screwdriver. Install the new battery and close the opening on the key fob.

Test the key fob by pressing the lock/unlock buttons. It's okay in case the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your keys need to be programmed, you will need to be aware of the number written on the key code tag and then record it in a safe location.

How do I replace the battery?

If the Kia key fob doesn't respond to pressing the lock/unlock button, it is most likely that the battery is not fully charged. A battery that is not functioning properly can cause other issues, such as the check engine light flashing or the engine not turning correctly. It is easy to replace key fob batteries using just two tools.

Before you begin the process before beginning the process, ensure that your vehicle is turned off and all doors are shut. Find the small metal or plastic piece on the bottom of the key fob. Then, jiggle it until the metal key is released. You can then insert the key into the handle of the door for the driver to unlock your car.

To replace the battery on the key fob, you must remove the cover at the rear. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and align the new battery in a way that the "+" positive side faces you, while the "negative" negative side is facing towards the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After installing the new battery and turning the key fob on and off in the ignition until the door locks up. You can then test the kia ceed replacement key's Key fob again to make sure it's working properly.

How do you replace a keyless key

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade, while the standard key fob does not. Both kinds of key fobs contain batteries inside that eventually will need to be replaced. It's a fairly simple process that only takes about two minutes.

Before you start, you will want to ensure that you are on a flat surface with adequate lighting and that your kia replacement key fob is not on. Keep in mind that there are tiny parts inside the fob that can fall out if not careful.

The release button for the small size is located on the lower backside. It's either an oval or circular slot. You can open the key fob by pressing the button.

After the key fob has been opened, take out the battery. The new battery is the CR-2032, and it can be purchased from a local or online auto parts shop. After installation it should be possible to lock, unlock and start your vehicle using your key fob - even if the engine isn't running!

How do you replace a mechanical key

The Kia keyfob is a wonderful convenience, allowing us to lock or unlock our car with just pressing the button. Like any device, the Kia key fob may have issues. There are methods to troubleshoot these issues and keep our key fobs in good condition over the long haul.

A dead or weak battery is one of the most frequent problems. This can cause your fob to stop working or operate intermittently. If this is the problem it is time to replace the battery an entirely new battery.

If this isn't enough to solve the issue, try using a flathead screwdriver standard to wedge the fob's plastic casing open. Be careful not to damage internal components, or scratch the plastic. After the battery has been removed and replaced with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to confirm it's functioning correctly. If the fob isn't working, contact a locksmith or dealer to resolve the issue. Make sure they cut you an emergency key that works for all door and trunk cylinders to avoid lockouts again.